Payment & Shipping Terms:
|FEATURES:||10 Years Minimum Data Retention In The Absence Of External Power||FEATURES2:||Data Is Automatically Protected During Power Loss|
|FEATURES3:||Replaces 32k X 8 Volatile Static RAM, EEPROM Or Flash Memory||Applications:||Unlimited Write Cycles|
|Typical Applications 1:||Low-power CMOS||Typical Applications 2:||Read And Write Access Times As Fast As 70 Ns|
low voltage power mosfet,
hybrid inverter circuit
DS1230Y-150+ 256k Nonvolatile SRAM SS Replaces RAM Module IC
10 years minimum data retention in the absence of external power
Data is automatically protected during power loss
Replaces 32k x 8 volatile static RAM, EEPROM or Flash memory
Unlimited write cycles
Read and write access times as fast as 70 ns
Lithium energy source is electrically disconnected to retain freshness until power is applied for the first time
Full ±10% VCC operating range (DS1230Y)
Optional ±5% VCC operating range (DS1230AB)
Optional industrial temperature range of -40°C to +85°C, designated IND
JEDEC standard 28-pin DIP package
New PowerCap Module (PCM) package
- Directly surface-mountable module
- Replaceable snap
-on PowerCap provides lithium backup battery
- Standardized pinout for all nonvolatile SRAM products
- Detachment feature on PowerCap allows easy removal using a regular screwdriver
A0 - A14 - Address Inputs
DQ0 - DQ7 - Data In/Data Out
CE - Chip Enable
WE - Write Enable
OE - Output Enable
VCC - Power (+5V)
GND - Ground
NC - No Connect
The DS1230 256k Nonvolatile SRAMs are 262,144-bit, fully static, nonvolatile SRAMs organized as 32,768 words by 8 bits.
Each NV SRAM has a self-contained lithium energy source and control circuitry which constantly monitors VCC for an out-of-tolerance condition.
When such a condition occurs, the lithium energy source is automatically switched on and write protection is unconditionally enabled to prevent data corruption.
DIP-package DS1230 devices can be used in place of existing 32k x 8 static RAMs directly conforming to the popular bytewide 28-pin DIP standard.
The DIP devices also match the pinout of 28256 EEPROMs, allowing direct substitution while enhancing performance. DS1230 devices in the Low Profile Module package are specifically designed for surface-mount applications.
There is no limit on the number of write cycles that can be executed and no additional support circuitry is required for microprocessor interfacing.
The DS1230 devices execute a read cycle whenever WE (Write Enable) is inactive (high) and CE (Chip Enable) and OE (Output Enable) are active (low).
The unique address specified by the 15 address inputs (A0 - A14) defines which of the 32,768 bytes of data is to be accessed. Valid data will be available to the eight data output drivers within tACC (Access Time) after the last address input signal is stable, providing that CE and OE (Output Enable) access times are also satisfied.
If OE and CE access times are not satisfied, then data access must be measured from the later-occurring signal (CE or OE ) and the limiting parameter is either tCO for CE or tOE for OE rather than address access.
The DS1230 devices execute a write cycle whenever the WE and CE signals are active (low) after address inputs are stable. The later-occurring falling edge of CE or WE will determine the start of the write cycle.
The write cycle is terminated by the earlier rising edge of CE or WE . All address inputs must be kept valid throughout the write cycle.
WE must return to the high state for a minimum recovery time (tWR) before another cycle can be initiated. The OE control signal should be kept inactive (high) during write cycles to avoid bus contention.
However, if the output drivers are enabled ( CE and OE active) then WE will disable the outputs in tODW from its falling edge.
|DS1230AB Power Supply Voltage||VCC||4.75||5.0||5.25||V||/|
|DS1230Y Power Supply Voltage||VCC||4.5||5.0||5.5||V|